Plug Removal Wrench
How to Check Your Spark Plugs
For the engine of any car to operate optimally, it requires good spark plugs and these plugs need to be replaced after approximately every twenty thousand miles. However, their condition needs to be checked after about ten thousand miles. This is normally done when the car goes for a tune up. It is also recommended by the manufacturer that the spark plugs are checked regularly incase of any splits, corrosion, cracks or any other damage that would interfere with the car’s performance. Checking the condition of the sparks does not require a qualified mechanic and the procedure for checking spark plugs is as follows.
First, pull the release lever for the hood which is located below the dash board. This will enable the hood to open. Move to the front of the vehicle and open up the hood with the latch underneath it. The spark plugs in four cylinder engines are found on a row that is on one side of the engine and cars which V-shaped engines have the plugs are on two sides of the engine. They need to be removed one at a time and thereafter; the plug wire should be replaced before checking another plug. The plug wire should then be pulled at the point where it connects to the plug. A rubber boot at the wire’s end is then pulled gently so as not to damage the plug.
Remove the plug with a ratchet and socket by twisting it counterclockwise. An extension of the ratchet and socket may be needed if the plugs are in a deep set and not easily accessible. Any dirt on the spark plug should be wiped or blown away to prevent anything getting in the cylinder. A spark plug in good condition should have a light coating of brown grayish deposits. If the plug happens to have a black coating or the core nose looks damaged then replacement is needed.
To carry out gapping of the spark plug, the correct gap should be determined from the car’s manual. It may also be indicated on the hood of the car. Put the gapping tool in the space that is between the centre electrode and the side electrode of the plug tip. Study the ruled edge of the tool and do a gap measurement. The gap can be adjusted by bending the tip of the spark plug to make the right size. This should be done for every plug. When putting in the new plugs, hand tighten them, and if resistance is felt then begin again to avoid cross threading. Socket wrenches are used to tighten them until they are securely in. The plug wires also require regular replacement. If gapping is not done appropriately, a car may not run properly and the right model of plugs should be bought for effective performance. The final step is to start the engine to find out whether the engine runs smoothly. Regular checking of spark plugs is vital to ensure that overall car safety is maintained.
About the Author
Enjoy your car and find the best deal on the insurance coverage you need. Visit us for money-saving tips, no-obligation auto insurance comparisons and advice for finding affordable insurance rates at Auto Insurance Rates Direct.
|
|
Lisle 14500 Oil Filter Socket $5.99 Removes and installs filters on 6 Liter Ford Diesel PickupsThe low profile socket fits both the 35mm and 36mm fuel and oil filtersThe low profile socket works in confined spaces3/8 in. driveNot for use with an impact wrench… |
|
|
GearWrench 80546 5/8-Inch x 6-Inch Swivel Spark Plug Socket $11.95 … |
|
|
Irwin Industrial Tools 394002 Bolt-Grip Expansion Set, 5-Piece $22.60 5 Piece BOLT-GRIP[TM] High Carbon Steel Expansion Set… |
|
|
Lisle (LIS65600) Broken Spark Plug Remover for Ford Triton 3 Valve Engines $53.50 Lisle Tools Creepers 65600 Brkn Plug Remvr Ford Triton… |
|
|
Plugmate Garboard Wrench Plugmate Garboard Plug Wrench $8.24 Plugmate Garboard Wrench Plugmate Garboard Plug Wrench Sea-Dog Line Plugmate Garboard Wrench – PLUGMATE GARBOARD PLUG WRENCH |
|
|
Nipple/Breech Plug Wrench Nipple/Breech Plug Wrench $10.11 NIPPLE/BREECH PLUG WRENCH Mfg: Marlin |
|
|
M1/M14/M1a Gas Cylinder Wrench Bad-T3 Wrench $34.99 Compact armorer-designed wrench enables fast easy disassembly of key gas system components for proper cleaning. A handy gas plug holder serves as a "third hand" that retains the gas plug for easy access and keeps it from getting lost while working on the gas system. The "D"-shaped hole in the center of the wrench supports the gas piston while using a gas piston carbon removal drill bit. BAD-T3 includes gas cylinder lock wrenches for the Garand and standard M14/M1A separate Garand and M14/M1A gas plug holders and the gas piston holder. Designed exclusively for M14/M1A variants the BAD-T4 has separate gas cylinder lock wrenches for the standard M14/M1A and the Smit Mfg: Battle Arms Development Inc. SPECS: Machined 7075 T6 aluminum hardcoat anodized. 5¾" (14.6cm) long 1½" (3.8cm) wide 3⁄8" (9.5mm) thick. |
|
|
M1/M14/M1a Gas Cylinder Wrench Bad-T4 Wrench $34.99 Compact armorer-designed wrench enables fast easy disassembly of key gas system components for proper cleaning. A handy gas plug holder serves as a "third hand" that retains the gas plug for easy access and keeps it from getting lost while working on the gas system. The "D"-shaped hole in the center of the wrench supports the gas piston while using a gas piston carbon removal drill bit. BAD-T3 includes gas cylinder lock wrenches for the Garand and standard M14/M1A separate Garand and M14/M1A gas plug holders and the gas piston holder. Designed exclusively for M14/M1A variants the BAD-T4 has separate gas cylinder lock wrenches for the standard M14/M1A and the Smit Mfg: Battle Arms Development Inc. SPECS: Machined 7075 T6 aluminum hardcoat anodized. 5¾" (14.6cm) long 1½" (3.8cm) wide 3⁄8" (9.5mm) thick. |
|
|
M14/M1a Gas Cylinder Wrench Gas Cylinder Wrench $22.99 Combination wrench holds the gas cylinder for easy gas plug removal without damage plus the D-shaped hole prevents the piston from moving during cleaning. Small enough to store in a pocket when at the range or in the field. Machined from ½" thick aluminum heat treated for extra strength with a long-wearing baked-on mil-spec coating. Rounded edges ensure a comfortable grasp. Mfg: Sadlak Industries SPECS: 6061 T6 aluminum O.D. green finish. 6" (14.6cm) long 1½" (3.8cm) wide ½" (6.3mm) thick. |
|
|
Garboard Drain Plug With Steel Wrench Garboard Drain Plug Socket Style $97.94 Garboard Drain Plug With Steel Wrench Garboard Drain Plug Socket Style Complete with Zinc Plated Steel Wrench |
